Furthermore, the Repetier server is already booted when operating in standby mode, this. 23:02:28,445 - DEBUG - Heater tool0 already off. Never turn on the heating bed while operating in standby mode. Okay so im trying to do the firmware flash on a davinci 2.0 (the one with the 2. 23:02:28,442 - DEBUG - Heater tool1 already off. So I do no think it is FW problem, check heater wires if not damaged. Symptom 3: (Was actually watching Octoprint this time) Hotend Dropped 50 C in the first 18 mins of Print. 23:02:28,440 - DEBUG - Heater bed already off. Symptom 1: Tool Light Started going out, Symptom 2: Fans would dip in and out assuming because the hotend temp was dipping. Turning heaters off prior to shutting off PSU. DEBUG - isPSUOn: True 23:02:28,437 - INFO - Idle timeout reached after 5 minute(s). We recommend to connect Repetier-Host to Repetier-Server. The debug log contains this interesting snippet where t looks like it’s going to shut off but then doesn’t: This implicates that you can not connect with any other software like Repetier-Host to the printer. After a print, it doesn’t work, even though it’s cooled down sufficiently. It works when the printer hasn’t been heated up yet. Ok, I thought it was working, but it’s not. After opening Repetier and connecting your 3D printer, select the manual control tab. Much swearing and checking of this forum blarz to the rescue Hit e-stop and the heated bed control appears and is functional. Fired it up on another machine with the newest Host version, no heated bed control. I suppose I could fix this with a GPIO pin, but it'd be a lot simpler if there was a way to configure PSU control to assume that the printer is on when the connection is established. Had the same issue today, ran a print last night from one PC with older Host version, no problem. When I switch my printer on, the hotends fan is not activated. This means that I have click the icon once manually in order to get it in sync every time the server restarts. When I order a heating, my printer cant reach the target temperature or takes a long. On launching Repetier-Host application, the main window of the application opens. The only remaining problem I have is that PSUControl starts up assuming that the PSU is off, when actually the PSU turns on automatically when Octoprint establishes the connection. Do not touch the heater when the 3D printer is working. Without the config I can't say what is wrong, but the most common error is changing this: / Index of analog sensor to read temperature of heated bed. So the question is what your error in the configuration.h file is. I changed it to a slightly more brute force regex of "Recv: T:*" and then the terminal filtering started working and possibly coincidentally, at the same time the idle timer for PSUControl seemed to start functioning as well. That the heated bed doesn't turn off is normal when the temperature reading is lower then target temperature. If you have PID enabled for your extruder, you will see the led starting to flicker when it comes within +/10C of the target temperature. Most boards also have a led signaling power to the heater. Turning heaters off prior to shutting off PSU. Use your host to change the temperature of your extruder and heated bed. Recv: T:18.45 /0 B:17.83 /0 doesn't match the default filtering regex. The debug log contains this interesting snippet where t looks like it’s going to shut off but then doesn’t: - DEBUG - isPSUOn: True 23:02:28,437 - INFO - Idle timeout reached after 5 minute(s). Does the idle timer implementation rely in any way on the string set for temperature command ignoring in the Octoprint terminal filter window? The reason I ask is that the terminal window was not previously filtering out the returned temp commands because repetier formats them like this: I'm not quite sure why, but the idle timer is now working.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |